|
|
1972
Ford Truck Wiring Diagrams |
|
|
|
NOTE - PLEASE READ!
The following wiring diagram is an EXTREMELY
LARGE file! It consists of the contents of EIGHT pages
that have been stitched together into a single file. In
fact, I have personally invested more than 100 man-hours
into this diagram. Please
be patient while it downloads. If you're on a dial-up
account, I feel sorry for ya!
Because of the physical dimensions of this file, some older
computers with limited resources might be unable to properly
display it. Therefore, this file has also been broken down
into seven smaller files which can be viewed and/or downloaded below.
To save to your computer for future use, just right-click on
the thumbnails below and choose "Save Link As...".
The diagram legend is also displayed below for help in
deciphering the diagram contents. |
|
4187p x 1536p ~ 1.01MB |
Connector Legend
Every harness connection in the above main wiring
diagrams is labeled with a connector ID number.
Refer to the legend at left for correct connector
pin-out. |
NOTE: This legend is accurately replicated
from the original OEM factory wiring diagrams,
including three connectors (C-24, C-38, C-80) which
have the same connector ID number but multiple
differing
pin-out variations. Therefore, be sure the diagram
you’re referring to on this legend coincides with
the connector’s physical location in the wiring
harness. The connectors with identical ID numbers
but different pin-outs are labeled to show their
location on the Master Wiring Diagram. |
Everything shown below this point will help you locate
and identify the various components, connectors, splices
and grounds shown in the above diagram(s). All
links will open in a new window, to allow this page to
remain open for reference.
|
Wire
Code |
To Ignition Switch
Direct to Battery
Bus Bar |
Ground
Codes |
-
G-1 - Eyelet attached to engine
block
-
G-2 - Eyelet attached to engine
block
-
G-3 - Eyelet attached to center
of the dash panel
-
G-4 - Eyelet attached to "Y"
brace under instrument panel
-
G-5 - Eyelet on heater case
-
G-6 - Eyelet attached to R.H.
inner cowl side panel
-
G-7 - Eyelet attached to frame
crossmember
-
G-8 - Eyelet attached to cab
inner back panel
-
G-9 - Eyelet attached to R.H.
radiator support
-
G-10 - Eyelet attached to L.H.
radiator support
-
G-11 - Eyelet attached to dash
panel L.H. side
-
G-12 - Eyelet attached to rear
quarter panel L.H. side
-
G-13 - Eyelet attached to rear
quarter panel R.H. side
-
G-14 - Eyelet attached to L.H.
cowl panel
-
G-15 - Eyelet attached to L.H.
side of platform frame rear
-
G-16 - Eyelet attached to rear
lamp bracket L.H. and R.H. side
-
G-17 - Eyelet attached to rear
end of frame L.H. and R.H. side
-
G-18 - Eyelet attached to L.H.
side of stone shield
-
G-19 - Eyelet attached to voltage
regulator mounting screw
-
G-20 - Eyelet attached to
speedometer mounting screw
|
Splice Codes |
-
S-1 - In 14305 Wiring Assy.
(Standard instrument cluster)
-
S-2 - In 14305 Wiring Assy.
(R.P.O. cluster)
-
S-3 - In 14305 Wiring Assy.
(R.P.O. cluster)
-
S-4 - In 14401 Wiring Assy. near
fuse panel
-
S-5 - In 14401 Wiring Assy. near
ignition switch or fuse panel
-
S-6 - In 14401 Wiring Assy. near
R.H. hood hinge (standard cluster)
-
S-7 - In 14401 Wiring Assy. near
ignition switch
-
S-8 - In Camper 14405 Wiring
Assy.
-
S-9 - In Camper 14405 Wiring
Assy.
-
S-10 - In Camper 14405 Wiring
Assy.
|
|
|
|
Want to link to
this site? Please save this banner to your hard drive to place on your
webpage.
The correct link to use is
http://www.fordification.com
|