Misc Parts in Sacramento

[fordkenstein]

After much lament, I sold my truck
I gave most of the extra parts I had to the guy I sold it to.
Many of the parts in the photos are already gone. Here's what I have left:
- Left and right inner front fenders
- Battery tray
- Radiator support
- Sheet metal for roof, lower bed sides, cab floor, and trans access panel
- Upper and lower, driver and passenger door hinges
- Forward and aft, driver and passenger rear leaf spring -to- frame brackets
- Motor mounts (302)
- Pedal assembly for clutch and brake
- Manual brake reservoir and steering box
- Gauge cluster
- Bench seat

Assorted Parts - smaller.JPG

Garage Full - smaller.JPG

Gauges 001 - smaller.JPG

[Kurt Combs]

What is the condition of the battery tray and what to you want for it shipped to 95453? (I'm two and a half hours from you in Lake County.)

[1971ford]

Howdy neighbor. I'm right here in Folsom too..

How's the benchseat? Any bad rips? I have a buddy who wants a replacement bench seat (his is all torn up).
The doors are gone eh?

[fordkenstein]

Kurt, here's a shot of the battery tray for you (still attached to the inner fender by one stubborn bolt)...

Battery Tray - smaller.JPG

The battery tray has only surface rust. Hard to tell from the photo, but easily blasted off and re-painted.

71Ford, here's a shot of the seat for you...

Seat - smaller.JPG

The seat would need recovering, but the tracks are there, and the stuffing appears to be in useable shape.

[goldies67]

id like both inner fenders! how much shipped to 02703

[fordkenstein]

Hi Goldies67,

How would you want them shipped?
They're big and reasonably heavy.
I've never shipped anything that size before.
$20 each plus shipping?

[89ford]

how much for the motor mounts?

[MattHillFord]

Hello from Oroville, CA
I'm wondering about the cab floor panels. What kind of condition is it in?

[fordkenstein]

Hello 89ford,

Does $10 plus shipping sound good for the motor mounts?
These are the frame-side and not the engine-side.
I'll post a pic later.

Hello MattHillFord,

My parts truck was in rough shape when I bought it.
It appeared to have spent many years as a farm truck that had moved bed-fulls of gravel many times!
No tailgate and no engine or radiator when I bought it.
I cut it up; scrapped some, and kept some.
In my project truck, someone before me had widened the trans access area.
I cut the floor out of the parts truck - door sill to door sill and half way up the firewall to the gas tank area.
From the trans access area up about 8 inches on the firewall and out about 8 inches on either side is gone into my project truck.
So, what I have left is partial driver and passenger floor pans and the floor section under the seat.
Both floor pans are what you would expect from a truck in this condition - no rust through, but lots of pitting, more on the passenger side (under the heater core), and more near the door sills on both sides.
I'll post a pic later.

[fordkenstein]

Howdy neighbor (1971ford),

I bought some miscellaneous parts from you last year.
A guy from Orangevale has contacted me about the seat.
I think he's going to pick it up tonight.
As for the doors, they went with my project truck.
The guy doesn't need them though - the doors on my truck are fine.
If you want, I can contact him to see if he'll sell them to you.
He lives in Midtown.

[fordkenstein]

Motor mounts & Inner Fenders...

Motor Mounts - smaller.JPG

Inner Fenders Top - smaller.JPG

Inner Fenders Bottom - smaller.JPG

[fordkenstein]

Cab floor...

Cab Floor 2 - smaller.JPG

Cab Floor 1 - smaller.JPG

[fordkenstein]

The seat has been sold!

[bb72ford]

Do you still have the radiator support or inner fenders?

[fordkenstein]

Still have both.