Anyone know the width of a bumpside 9" housing and a D60 housing? Are they the same width flange-to-flange? Lookin' for a diagram on here but not finding one with dimensions...Rear axle widths?
Moderators: FORDification, 70_F100
-
F100builder
- Blue Oval Guru
- Posts: 1304
- Joined: Thu Jan 10, 2008 6:55 pm
- Location: Idaho, Nampa
Rear axle widths?
It's too hot outside to run my tape measure... Anyone know the width of a bumpside 9" housing and a D60 housing? Are they the same width flange-to-flange? Lookin' for a diagram on here but not finding one with dimensions...
Anyone know the width of a bumpside 9" housing and a D60 housing? Are they the same width flange-to-flange? Lookin' for a diagram on here but not finding one with dimensions...Patrick
'56 F100; Must.II IFS, 351W bored & stroked to 395c.i. 470hp/483ft-lbs., AOD, 4-link coilover 9" w/ 3.89's
'69 F100; 390, C6, Dana 60 w/ 4.10's
'70 F100; 'new' and latest project soon to have a built 390/C6 and 3.50 gears
To see more of my F100's: http://www.cardomain.com/id/lowfat56
'56 F100; Must.II IFS, 351W bored & stroked to 395c.i. 470hp/483ft-lbs., AOD, 4-link coilover 9" w/ 3.89's
'69 F100; 390, C6, Dana 60 w/ 4.10's
'70 F100; 'new' and latest project soon to have a built 390/C6 and 3.50 gears
To see more of my F100's: http://www.cardomain.com/id/lowfat56
-
fordman
- 100% FORDified!
- Posts: 22329
- Joined: Sun Aug 28, 2005 8:17 pm
- Location: Kansas, Ottawa
- Contact:
Re: Rear axle widths?
9 inch axles are 29 7/8. i think that is to the inside of the lugs flange. not the outside.
-
F100builder
- Blue Oval Guru
- Posts: 1304
- Joined: Thu Jan 10, 2008 6:55 pm
- Location: Idaho, Nampa
Re: Rear axle widths?
So, outside of drum to outside of drum?fordman wrote:9 inch axles are 29 7/8. i think that is to the inside of the lugs flange. not the outside.
Patrick
'56 F100; Must.II IFS, 351W bored & stroked to 395c.i. 470hp/483ft-lbs., AOD, 4-link coilover 9" w/ 3.89's
'69 F100; 390, C6, Dana 60 w/ 4.10's
'70 F100; 'new' and latest project soon to have a built 390/C6 and 3.50 gears
To see more of my F100's: http://www.cardomain.com/id/lowfat56
'56 F100; Must.II IFS, 351W bored & stroked to 395c.i. 470hp/483ft-lbs., AOD, 4-link coilover 9" w/ 3.89's
'69 F100; 390, C6, Dana 60 w/ 4.10's
'70 F100; 'new' and latest project soon to have a built 390/C6 and 3.50 gears
To see more of my F100's: http://www.cardomain.com/id/lowfat56
-
fordman
- 100% FORDified!
- Posts: 22329
- Joined: Sun Aug 28, 2005 8:17 pm
- Location: Kansas, Ottawa
- Contact:
Re: Rear axle widths?
that is each axle. when pulled out measuring it from the end of splines to the inside of the lug bolt flange.
You do not have the required permissions to view the files attached to this post.
-
F100builder
- Blue Oval Guru
- Posts: 1304
- Joined: Thu Jan 10, 2008 6:55 pm
- Location: Idaho, Nampa
Re: Rear axle widths?
Oh, OK. Thanks Craig but I was talking about the flange to flange measurement of the housing...
A measurement from drum to drum or backing plate to backing plate would be fine too.
A measurement from drum to drum or backing plate to backing plate would be fine too.
Patrick
'56 F100; Must.II IFS, 351W bored & stroked to 395c.i. 470hp/483ft-lbs., AOD, 4-link coilover 9" w/ 3.89's
'69 F100; 390, C6, Dana 60 w/ 4.10's
'70 F100; 'new' and latest project soon to have a built 390/C6 and 3.50 gears
To see more of my F100's: http://www.cardomain.com/id/lowfat56
'56 F100; Must.II IFS, 351W bored & stroked to 395c.i. 470hp/483ft-lbs., AOD, 4-link coilover 9" w/ 3.89's
'69 F100; 390, C6, Dana 60 w/ 4.10's
'70 F100; 'new' and latest project soon to have a built 390/C6 and 3.50 gears
To see more of my F100's: http://www.cardomain.com/id/lowfat56
-
fordman
- 100% FORDified!
- Posts: 22329
- Joined: Sun Aug 28, 2005 8:17 pm
- Location: Kansas, Ottawa
- Contact:
-
F100builder
- Blue Oval Guru
- Posts: 1304
- Joined: Thu Jan 10, 2008 6:55 pm
- Location: Idaho, Nampa
Re: Rear axle widths?
Thank you! 
Patrick
'56 F100; Must.II IFS, 351W bored & stroked to 395c.i. 470hp/483ft-lbs., AOD, 4-link coilover 9" w/ 3.89's
'69 F100; 390, C6, Dana 60 w/ 4.10's
'70 F100; 'new' and latest project soon to have a built 390/C6 and 3.50 gears
To see more of my F100's: http://www.cardomain.com/id/lowfat56
'56 F100; Must.II IFS, 351W bored & stroked to 395c.i. 470hp/483ft-lbs., AOD, 4-link coilover 9" w/ 3.89's
'69 F100; 390, C6, Dana 60 w/ 4.10's
'70 F100; 'new' and latest project soon to have a built 390/C6 and 3.50 gears
To see more of my F100's: http://www.cardomain.com/id/lowfat56