Changing rear ends

Clutch, transmission, rear axle

Moderators: FORDification, 70_F100

Post Reply
robs72
New Member
New Member
Posts: 2
Joined: Mon Oct 11, 2010 3:39 pm

Changing rear ends

Post by robs72 »

Any advice on a little better freeway gear ratio on my 72 f250 360 2bl, 2wd... Looking for a little better cruising, rather than pulling.

Thanks
User avatar
70_F100
Moderator
Moderator
Posts: 2999
Joined: Mon Oct 22, 2007 11:23 am
Location: North Carolina, Kernersville

Re: Changing rear ends

Post by 70_F100 »

What's the gear ratio that's in it now???
Wise men talk because they have something to say; fools talk because they have to say something.--Plato
Why is it that there's seldom time to fix it right the first time, but there's always time to fix it right the second time???

That's not an oil leak :nono: That's SWEAT from all that HORSEPOWER!! :thup:
User avatar
Caseys71
Blue Oval Guru
Blue Oval Guru
Posts: 1289
Joined: Sat Nov 07, 2009 7:48 pm
Location: Hampstead, North Carolina

Re: Changing rear ends

Post by Caseys71 »

70_F100 wrote:What's the gear ratio that's in it now???
:yt:, But most guys that are just using there trucks for cruising and looking to get decent MPG's usually go with around a 3.25 ratio that's with 235/75 tires, in theory you could just run a taller rear tire than what you have to get a higher gear ratio which would be better for cruising. Then again it would depend on the ratio you have now, and the tire size you have now.
Casey
16 years old with a 40 year old truck (well almost)
Image
1971 F-100302, T-18 4 speed, 3:55 rear, & an Edelbrock sticker on the ashtray.
"Don't worry about what you become, just make sure that you're successful at what you do."- Mr. English
"Value what you DO have over that which you don't."- Forrestbump
"Wanting can sometimes be better than having, never stop dreaming... it's what keeps us all going."- Forrestbump
1984 Toyota 4x4: 22-R, 5-speed, 3" suspension lift, 35's and 5:29's
fordman
100% FORDified!
100% FORDified!
Posts: 22329
Joined: Sun Aug 28, 2005 8:17 pm
Location: Kansas, Ottawa
Contact:

Re: Changing rear ends

Post by fordman »

i have a 3.25 390 with a c6 in my truck. and it pretty much gets 10 mpg. about a 1/4 tank for 15 miles and maybe back i think it used to run.
User avatar
70_F100
Moderator
Moderator
Posts: 2999
Joined: Mon Oct 22, 2007 11:23 am
Location: North Carolina, Kernersville

Re: Changing rear ends

Post by 70_F100 »

fordman wrote:i have a 3.25 390 with a c6 in my truck. and it pretty much gets 10 mpg. about a 1/4 tank for 15 miles and maybe back i think it used to run.
:yt:

I've got 3.25 in mine, and with a C6 and 360, just like Fordman said, 10 mpg. That's uphill, downhill, headwind, tailwind, empty, loaded, towing, even just sitting in my driveway... :lol:

Since I put the T19 in and swapped to 265/75-15's, I haven't driven it anywhere except around the neighborhood, so I don't know about the mileage. :doh: I'm pretty sure that going to a manual tranny and larger tires will help, but I still don't anticipate a lot of improvement.
Wise men talk because they have something to say; fools talk because they have to say something.--Plato
Why is it that there's seldom time to fix it right the first time, but there's always time to fix it right the second time???

That's not an oil leak :nono: That's SWEAT from all that HORSEPOWER!! :thup:
robs72
New Member
New Member
Posts: 2
Joined: Mon Oct 11, 2010 3:39 pm

Re: Changing rear ends

Post by robs72 »

Thanks for all the advise, I am currently runnning 3.73 stock gears. I will look into the 3.25, it sounds like what I am looking for.

Thanks Again to all
ScreaminZ
New Member
New Member
Posts: 217
Joined: Fri Jan 09, 2009 10:54 am
Location: Crowley, TX

Re: Changing rear ends

Post by ScreaminZ »

I could be mistaken, but I don't think you're going to find any gear ratios numerically lower than 3.54 if your rear axle is a Dana 60. These other guys talking about a 3.25 ratio are more than likely talking about F100's with a 9-inch rear end.
User avatar
70_F100
Moderator
Moderator
Posts: 2999
Joined: Mon Oct 22, 2007 11:23 am
Location: North Carolina, Kernersville

Re: Changing rear ends

Post by 70_F100 »

ScreaminZ wrote:I could be mistaken, but I don't think you're going to find any gear ratios numerically lower than 3.54 if your rear axle is a Dana 60. These other guys talking about a 3.25 ratio are more than likely talking about F100's with a 9-inch rear end.
Yep, that's what mine is.
Wise men talk because they have something to say; fools talk because they have to say something.--Plato
Why is it that there's seldom time to fix it right the first time, but there's always time to fix it right the second time???

That's not an oil leak :nono: That's SWEAT from all that HORSEPOWER!! :thup:
Post Reply