B&M c6 tranny pan

flakos 69 · Post by **flakos 69** » Thu Aug 26, 2010 4:28 pm

would i fit without messing with the frame support

ForingaMex · Post by **ForingaMex** » Thu Aug 26, 2010 5:51 pm

I'm not sure but isn't the crossmember in front of the pan? Just thinkin...

fordman · Post by **fordman** » Thu Aug 26, 2010 6:41 pm

i think he is thinking about the rear crossmember.

flakos 69 · Post by **flakos 69** » Thu Aug 26, 2010 7:23 pm

my worry is the cross member between the strut rod bushings

fordman · Post by **fordman** » Thu Aug 26, 2010 7:27 pm

oops i was wrong.

basketcase0302 · Post by **basketcase0302** » Thu Aug 26, 2010 8:16 pm

I've got plenty of room under my little 302 with the C-6 for a deeper pan, (it's on my "wish list" someday).
What engine you have in the truck? F-100/250/350?

flakos 69 · Post by **flakos 69** » Fri Aug 27, 2010 11:39 am

F100 390fe c6 shorty
I have one on a dent side parts truck but the cross member looks different dont know if it was cut

basketcase0302 · Post by **basketcase0302** » Sat Aug 28, 2010 6:53 am

flakos 69 on Fri Aug 27, 2010 11:39 am
F100 390fe c6 shorty

This probably won't help you then? Hopefully someone else here, (Bobby maybe) can pipe in that has a BBF or an FE/C-6 combo.

Here's the best picture i have of my little 302 with the C-6, but it doesn't really show the crossmember at all...

pritch1958 · Post by **pritch1958** » Sat Aug 28, 2010 2:44 pm

Up until recently I had my '68 bump with a C6 with a B&M Deep pan on it. I think i had to file the leading edge of the fins down to a 45 for a little bit of clearance, but i'm not positive. It might have been the AOD before it that i had to do that to. I'll go look at the pan this afternoon to be for sure, but either way it was on there without any real issue with the front crossmember.

pritch1958 · Post by **pritch1958** » Sat Aug 28, 2010 7:31 pm

I just looked at mine and its a TCI cast aluminum deep pans, but I didn't have to modify it.

flakos 69 · Post by **flakos 69** » Mon Aug 30, 2010 12:01 am

seems that the crossmember is different on the dent side I will get pictures tomorrow

I started to remove the 69's hopefully they interchange

flakos 69 · Post by **flakos 69** » Wed Sep 15, 2010 6:41 pm

IMAG0057.jpg

IMAG0058.jpg

IMAG0059.jpg

the narrow cross member is the one off the 76 the wide one is off the 69

big block · Post by **big block** » Fri Sep 17, 2010 6:55 am

the eariler cross member like the one i have is pretty close to my deep c-6 tci pan 1/4 in but it clears but is a 65 w/ 429 c-6 but ford didnt like to change things a whole lot. wes

The FORDification.com Forums

B&M c6 tranny pan

B&M c6 tranny pan

Re: B&M c6 tranny pan

Re: B&M c6 tranny pan

Re: B&M c6 tranny pan

Re: B&M c6 tranny pan

Re: B&M c6 tranny pan

Re: B&M c6 tranny pan

Re: B&M c6 tranny pan

Re: B&M c6 tranny pan

Re: B&M c6 tranny pan

Re: B&M c6 tranny pan

Re: B&M c6 tranny pan

Re: B&M c6 tranny pan