headers for 460
Moderators: Ranchero50, DuckRyder
headers for 460
ok, the headers that i have almost drag the ground, ive had enough. i need to find a set that will come down OVER the crossmember like my 390 headers did. the ones i have are real fancy so it makes them hard to give up, but i can barely get in my driveway. thing is i cant find any that state where they come out, all the research shows they come under the crossmember . the rest i coulndt find out about. has anyone used a quality set that went over the crossmember?? any feedback is appreciated
- 1971ford
- 100% FORDified!
- Posts: 5565
- Joined: Wed Jul 04, 2007 1:05 pm
- Location: Placerville CA
Re: headers for 460
when we put the 429 in the 71 i got hedman headers from summit. there not fancy if your looking for more of a high-quality performance header.
i think these are them: http://store.summitracing.com/partdetai ... toview=sku
they go above the crossmember but its a tight fit. we cut a little notch into the frame.
only picture...
if you want i can get better pictures for you.
i think these are them: http://store.summitracing.com/partdetai ... toview=sku
they go above the crossmember but its a tight fit. we cut a little notch into the frame.
only picture...
if you want i can get better pictures for you.
-Ryan
- Dragon
- 100% FORDified!
- Posts: 2659
- Joined: Sat Feb 16, 2008 4:43 pm
- Location: Albuquerque, New Mexico
- Contact:
Re: headers for 460
What brand did you buy? Even Hooker racing headers for our trucks go through the same place as all I have seen.70shortwide wrote:ok, the headers that i have almost drag the ground, ive had enough. i need to find a set that will come down OVER the crossmember like my 390 headers did. the ones i have are real fancy so it makes them hard to give up, but i can barely get in my driveway. thing is i cant find any that state where they come out, all the research shows they come under the crossmember . the rest i coulndt find out about. has anyone used a quality set that went over the crossmember?? any feedback is appreciated
3 inch collectors make it real tight but they do fit.
Old Fords Rule
Was a Ford Service Tech
71 F250 with Shell Car 390 NP435 Dana 60 3.73s, PS, PB, 750 EC VS Holley Accel Points Eliminator.
98 Volvo S70 2.4T Auto
71 Service manuals Volumes 1,2,3 and 4 So ask away.
My Gallery
Spark test
Was a Ford Service Tech
71 F250 with Shell Car 390 NP435 Dana 60 3.73s, PS, PB, 750 EC VS Holley Accel Points Eliminator.
98 Volvo S70 2.4T Auto
71 Service manuals Volumes 1,2,3 and 4 So ask away.
My Gallery
Spark test
Re: headers for 460
thanks for the link. i may send you a pm for more pics1971ford wrote:when we put the 429 in the 71 i got hedman headers from summit. there not fancy if your looking for more of a high-quality performance header.
i think these are them: http://store.summitracing.com/partdetai ... toview=sku
they go above the crossmember but its a tight fit. we cut a little notch into the frame.
only picture...
if you want i can get better pictures for you.
Ive got Doug Thorleys. they used to be real nice... 1 7/8 primarys and chromeDragon wrote:
What brand did you buy? Even Hooker racing headers for our trucks go through the same place as all I have seen.
3 inch collectors make it real tight but they do fit.
Re: headers for 460
http://www.landlproducts.com/details.as ... temID=1087
A guy i know has these on his 4wd, hes pretty sure they will fit 2wd as well. anyone know why they wouldnt? the only thing that he mentioned and i see is that the drivers side turns in towards the oild pan just a touch. im pretty sure my exhaust guy wont have any trouble with it. any thoughts?
A guy i know has these on his 4wd, hes pretty sure they will fit 2wd as well. anyone know why they wouldnt? the only thing that he mentioned and i see is that the drivers side turns in towards the oild pan just a touch. im pretty sure my exhaust guy wont have any trouble with it. any thoughts?
- Dragon
- 100% FORDified!
- Posts: 2659
- Joined: Sat Feb 16, 2008 4:43 pm
- Location: Albuquerque, New Mexico
- Contact:
Re: headers for 460
Those are very unequal length headers great for the street look of headers but lousy for performance.
Old Fords Rule
Was a Ford Service Tech
71 F250 with Shell Car 390 NP435 Dana 60 3.73s, PS, PB, 750 EC VS Holley Accel Points Eliminator.
98 Volvo S70 2.4T Auto
71 Service manuals Volumes 1,2,3 and 4 So ask away.
My Gallery
Spark test
Was a Ford Service Tech
71 F250 with Shell Car 390 NP435 Dana 60 3.73s, PS, PB, 750 EC VS Holley Accel Points Eliminator.
98 Volvo S70 2.4T Auto
71 Service manuals Volumes 1,2,3 and 4 So ask away.
My Gallery
Spark test
Re: headers for 460
that was my first thought. if you look at the collector on the right side of the engine it is much longer. i assume this is to help even them out some. not saying theyre equal, but it looks as if theyve tried a little. I found a used set just now on craigslist, might give them a try. my motor way outperforms the traction that i have at this point, so Im not too worried about a perfectly tuned header. yet. itll still go way faster than sitting in my garage on jackstands . anyone ever try these? itd be nice to hear that they fit..
- convincor
- 100% FORDified!
- Posts: 1511
- Joined: Wed Sep 12, 2007 5:05 am
- Location: Connecticut
Re: headers for 460
you may want to look into Sanderson's
http://www.sandersonheaders.com/product ... cts_id=185
or
http://www.sandersonheaders.com/product ... ucts_id=89
http://www.sandersonheaders.com/product ... cts_id=185
or
http://www.sandersonheaders.com/product ... ucts_id=89
68 Custom Cab Shorty, 390, C6, 9"-3.50:1 Currie T/L
"Still Plays With Trucks"
http://s101.photobucket.com/albums/m41/convincor/F100/
"Still Plays With Trucks"
http://s101.photobucket.com/albums/m41/convincor/F100/
- Dragon
- 100% FORDified!
- Posts: 2659
- Joined: Sat Feb 16, 2008 4:43 pm
- Location: Albuquerque, New Mexico
- Contact:
Re: headers for 460
Also if you run a carb the carb will be radically lean on one side or rich depending on which side you look at. One side will scavenge at lower RPM than the other. This alters the air flow through the engine.
Old Fords Rule
Was a Ford Service Tech
71 F250 with Shell Car 390 NP435 Dana 60 3.73s, PS, PB, 750 EC VS Holley Accel Points Eliminator.
98 Volvo S70 2.4T Auto
71 Service manuals Volumes 1,2,3 and 4 So ask away.
My Gallery
Spark test
Was a Ford Service Tech
71 F250 with Shell Car 390 NP435 Dana 60 3.73s, PS, PB, 750 EC VS Holley Accel Points Eliminator.
98 Volvo S70 2.4T Auto
71 Service manuals Volumes 1,2,3 and 4 So ask away.
My Gallery
Spark test
Re: headers for 460
yea, i talked with sanderson. they told me that theyd guarrantee a set to fit. problem i have is that their customer service record is horrible. ive read reviews where people had defects in their headers and could not get them to do anything about it. also met a guy that bought some for his 460 cobra jet heads that they "guaranteed" to fit. when he called them to tell them that they had the wrong flanges for his head they told him he was wrong and that he wasnt putting them on right...
l&l seems to be ok. I havent heard bad things about them. id like to give them a try, I dont know any reason they wouldnt fit except i dont have a set to try. im gonna try to get a look at my buddies truck that has them so i can at least eyeball a fit.
l&l seems to be ok. I havent heard bad things about them. id like to give them a try, I dont know any reason they wouldnt fit except i dont have a set to try. im gonna try to get a look at my buddies truck that has them so i can at least eyeball a fit.
- iamthewreckingcrew
- New Member
- Posts: 194
- Joined: Sun Apr 08, 2007 5:36 pm
- Location: Iowa
Re: headers for 460
I bought the same ones as 1971Ford. The Hedmans. They exit above the crossmember.
68 F-100 Short Box 2wd
302/c4/3.50
81 F-100 Long Box 2wd
460/c6/3.00
92 F-150 Lariat 4wd
302/auto couldn't go wrong for $500
302/c4/3.50
81 F-100 Long Box 2wd
460/c6/3.00
92 F-150 Lariat 4wd
302/auto couldn't go wrong for $500
- OldRedFord
- Blue Oval Guru
- Posts: 1314
- Joined: Tue Jan 29, 2008 11:37 pm
- Location: Hull GA
- Contact:
Re: headers for 460
1971ford wrote:when we put the 429 in the 71 i got hedman headers from summit. there not fancy if your looking for more of a high-quality performance header.
i think these are them: http://store.summitracing.com/partdetai ... toview=sku
they go above the crossmember but its a tight fit. we cut a little notch into the frame.
only picture...
if you want i can get better pictures for you.
Sorry to drag this thread back up, but what did you have to notch exactly?
Tim
1972 F350 flatbed drw c6/390
1967 F600 project truck
1972 F350 flatbed drw c6/390
1967 F600 project truck
- 1971ford
- 100% FORDified!
- Posts: 5565
- Joined: Wed Jul 04, 2007 1:05 pm
- Location: Placerville CA
Re: headers for 460
ill try to remember to get more pictures later today to show you guys, but basically we had to do one frame notch. If i remember correctly the notch is a inch long, and goes about 1/2 inch deep. It is located on the passenger side, where all the tubes come together. Ill have to check it out and get pictures
-Ryan